Washer (DIN 433) made of PA

Technical specification Material: PA 6.6 (polyamide 66) Colour: natural... more

Close menu

Technical specification

Material: PA 6.6 (polyamide 66)

Colour: natural

Regulations: DIN 433, ISO 7092

General Information Universal washers or spacer rings Ideal sliding rings between rotating... more

Close menu

General Information

Universal washers or spacer rings

Ideal sliding rings between rotating parts

Insulate moisture and electricity

Absorb vibrations

Chemical features:

Resistant to aromatic and aliphatic hydrocarbons, fuels, mineral oils and mineral lubricants; suitable for alkohols, esters, ketones, ethers and amines; good resistance to weak alkalis, but only moderate resistance to strong alkalis; limited resistance to weak mineral and organic acids; not resistant to oxidizing acids, strong mineral and organic acids as well as phenols; limited resistance to hydrolysis

Material specification:

Polyamide is an elastic, tough, loadable, but notch-sensitive material

Impact resistant

Resistant to abrasion and cold

High fatigue strength and excellent resilience

High wear resistance and good mechanical damping capacity

Insulating properties and an amazingly high tensile strength

Connecting parts made of polyamide and similar plastics protect from rust and corrosion damage

Polyamide can also be used in the food processing industry and in medical fields

PA 6 features a higher impact resistance compared to PA 6.6

PA 6 has the highest water absorption of all common plastics up to 9 to 10 % (followed by PA 6.6 with 8 to 9 %), thus considerably increased toughness, flexibility and elongation. However, the strength of the material can therefore be reduced by up to 10 %.

Material: PA 6 (polyamide 6)

Colour: natural

Density: approx. 1.14 g/cm³

Temperature range: -40 to +85 °C, for a short time +180 °C

Melting temperature: +220 °C (ISO 11357)

Yield stress: 75 MPa (ISO 527)

Elongation at break: >50 % (ISO 527)

Elastic modulus: 3,200 MPa (ISO 527)

Impact resistance: without break (DIN 53453)

Notch impact strength (Charpy): >3 kJ/m² (ISO 179)

Ball pressure hardness: 160 N/mm² (ISO 2039-1)

Shore hardness D: 82° (DIN 53505)

Dielectric strength: 20 kV/mm (IEC 60243)

Dielectric constant: 3.9 at 50 Hz (IEC 60250)

Surface resistance: 10¹³ Ohm (IEC 60093)

Volume resistivity: 10¹⁵ Ohm x cm (IEC 60093)

Comparative tracking index (CTI): >600 (DIN 53480)

Dielectric loss factor (at 50 Hz): 0.02 (specimen dry)

Water absorption: up to 10 % (during storage in water) (DIN 53472)

Flammability rating: UL 94 HB

Item	For thread	d mm	D mm	h mm	Einheit Stück	Price Euro*
308994	M2	2,2	4,5	0,3	50	9.00
308995	M2	2,2	4,5	0,3	100	15.00
336234	M2,5	2,7	5	0,5	50	10.00
336235	M2,5	2,7	5	0,5	100	17.00
308996	M3	3,2	6	0,5	50	10.00
308997	M3	3,2	6	0,5	100	17.00
308998	M4	4,3	8	0,5	50	12.00
308999	M4	4,3	8	0,5	100	19.00
309000	M5	5,3	9	1	50	19.00
309001	M5	5,3	9	1	100	32.00
306740	M6	6,4	11	1,5	50	23.00
336913	M6	6,4	11	1,5	100	38.00
336914	M8	8,4	15	1,6	50	23.00
336233	M8	8,4	15	1,6	100	38.00
309002	M10	10,5	18	1,6	50	23.00
309003	M10	10,5	18	1,6	100	38.00
336241	M12	13	20	2	50	36.00
336242	M12	13	20	2	100	60.00
309004	M14	15	24	2,5	25	35.00
309005	M14	15	24	2,5	50	58.00
309006	M16	17	28	2,5	25	43.00
309007	M16	17	28	2,5	50	71.00
309008	M18	19	30	2,5	25	43.00
309009	M18	19	30	2,5	50	71.00
309010	M20	21	34	3	25	52.00
309011	M20	21	34	3	50	84.00