T-Shaped Pipe Connector with Male Thread made of PP, PVDF or PTFE

T-Shaped Pipe Connector with Male Thread made of PP, PVDF or PTFE

Product specification T-shape, pipe connection on two sides; male G-, NPT- or M-thread on the... more

Close menu

Product specification

T-shape, pipe connection on two sides; male G-, NPT- or M-thread on the third side

General Information EMP-4 THOMAFLUID ® -pipe screw fittings are used for connecting pipes... more

Close menu

General Information EMP-4

THOMAFLUID^®-pipe screw fittings are used for connecting pipes made of various materials such as metal, glass or plastic e.g. PA, PTFE or PVDF. This represents a considerable advantage of this kind of screwed fittings. The screw fitting is not limited to use with rigid pipes but also with flexible pipes or tubing. In this case, carrying brackets (items 22036-54) are required.

THOMAFLUID^®-pipe screw fittings of the MULTIFIT^®-EMP-series can be screwed into THOMAFLUID^®-valves, cocks, and flowmeters of the MULTIFIT^®-EMP-series.

Assembly:

The connection principle entails pushing the pipe against the inner edge of the connector and sealing with a sealing ring. The pipe is secured in place by a cutting ring (PEEK), which is forced against the pipe by a nut. The more the nut is screwed onto the connector body, the more the slotted cutting ring wedges the pipe. The result is a tight, friction-locked connection, which can be released at any time. The design concept eliminates the dead volume. It also has no effect on the flow because the inside diameter is identical to that of the pipe.

If flexible tubing has have to be adapted using THOMAFLUID^®-pipe screw fittings, first the carrying brackets have to be put in the flexible tubes. Afterwards, the fixed assembly is done by tightening the cap nut.

PP (Polypropylene)

Extremely good impact toughness and notch impact strength

Higher hardness and stiffness as well as better resilience than PE

Thermoforming possible

Very good dielectrical properties

Good resistance to alcohols, ketones, conc. acids and alkalis

Not stable to aromatic hydrocarbons, fats and oils, halogenes

Autoclavable

Resistant to hydrolysis

Physiologically safe

Regulatory compliance to FDA 21 CFR 177.1520, RoHS, BPA-free, DEHP-free, BSE/ADI-free

Colour: grey

Density: 0.90 g/cm³

Temperature range: +5 to +90 °C

Shore hardness D: 72°

Max. operating pressure: 10 bar at +20 °C

Water absorption: <0.05 %

Tensile strength: 25 - 40 N/mm²

Elongation at break: 800 %

Surface resistance: >10¹³ Ohm

Melt flow index MFR: 0.3 g/10 min.

PVDF (Polyvinylidene fluoride)

High-quality technical plastic for chemical apparatus and machine building, especially in the petrochemical, metallurgical, pharmaceutical, food processing, paper and textile industry as well as in the nuclear technology.

High impact toughness even at low temperatures

Good breakdown strength

Low dielectric loss factor

Highest mechanical stability and stiffness

Meeting highest purity requirements

Comply with the guidelines from FDA, BSE/ADI-free and USP class VI, additionally PVDF has the KTW approval. Up to +150 °C it is non-toxic and since it has a similar property to glass it is a no-culture medium for microorganisms.

Can be treated by autoclave (absolute sterile) and sterilized with gamma-rays without losing its mechanical qualities

Outstanding resistance to UV, weather and aging

Flame-resistant

High thermal stability

Resistant to alcohols, fats and oils, halogenes, alkalis, acids

Not stable to aromatic hydrocarbons, ketones, amines, pyridine, dimethylformamide, hot alkalis, fuming sulfuric acid

Colour: nature, slightly translucent

Density: 1.75 g/cm³

Temperature range: -40 to +140 °C

Shore hardness D: 79°

Max. operating pressure: 10 bar at +20 °C

Water absorption: <0.04 %

Tensile strength: 38 - 50 N/mm²

Surface resistance: >10¹³ Ohm

Melt flow index MFR: 6 g/10 min.

PTFE (Polytetrafluoroethylene)

Heavy-duty plastic

Antiadhesive surface

Outstanding sliding properties

Lowest friction coefficient of all fluorinated plastics

Excellent stress cracking resistance

Excellent weather resistance

Highest gas-tightness

No water absorption

Very good dielectric properties independent of frequency and temperature

Very good electrical insulating capacity also at air humidity

High tracking resistance

Non-combustible

Colour: milky, white

Density: 2.20 g/cm³

Temperature range: -200 to +150 °C

Shore hardness D: 60°

Max. operating pressure: 6 bar at +20 °C

Tearing strength: 30 - 40 N/mm²

Elongation at break: 300 %

Water absorption: 0.01 %

Surface resistance: >10¹⁷ Ohm

Item	Pipe outside Ø mm	Außengewinde	D mm	l1 mm	L1 mm	L2 mm	Werkstoff	Einheit Stück	Price Euro*
10699	4	G 1/8"	15	8	48	23	PP	10	150.00
10701	4	G 1/8"	15	8	48	23	PVDF	1	125.00
10702	4	G 1/4"	15	12	48	27	PP	10	150.00
10704	4	G 1/4"	15	12	48	27	PVDF	1	110.00
10705	4	G 3/8"	20	12	54	27	PP	10	300.00
10707	4	G 3/8"	20	12	54	27	PVDF	1	144.00
10708	4	G 1/2"	25	14	60	29	PP	10	322.00
10710	4	G 1/2"	25	14	60	29	PVDF	1	157.00
23039	6	G 1/8"	15	8	48	23	PP	10	144.00
23041	6	G 1/8"	15	8	48	23	PVDF	1	125.00
23043	6	G 1/4"	15	12	48	27	PP	10	150.00
23044	6	G 1/4"	15	12	48	27	PTFE	1	140.00
23045	6	G 1/4"	15	12	48	27	PVDF	1	125.00
23047	6	G 3/8"	20	12	54	27	PP	10	300.00
23049	6	G 3/8"	20	12	54	27	PVDF	1	143.00
23051	6	G 1/2"	25	14	60	29	PP	10	322.00
23053	6	G 1/2"	25	14	60	29	PVDF	1	157.00
23055	8	G 1/8"	15	8	48	24	PP	10	304.00
23057	8	G 1/8"	15	8	48	24	PVDF	1	157.00
23059	8	G 1/4"	15	12	48	28	PP	10	322.00
23061	8	G 1/4"	15	12	48	28	PVDF	1	157.00
23063	8	G 3/8"	20	12	54	28	PP	10	328.00
23065	8	G 3/8"	20	12	54	28	PVDF	1	156.00
23067	8	G 1/2"	25	14	60	30	PP	10	364.00
23069	8	G 1/2"	25	14	60	30	PVDF	1	185.00
23071	10	G 1/8"	20	8	56	26	PP	10	364.00
23073	10	G 1/8"	20	8	56	26	PVDF	1	185.00
23075	10	G 1/4"	20	12	56	30	PP	10	364.00
23077	10	G 1/4"	20	12	56	30	PVDF	1	185.00
23079	10	G 3/8"	20	12	56	30	PP	10	352.00
23081	10	G 3/8"	20	12	56	30	PVDF	1	185.00
23083	10	G 1/2"	25	14	62	32	PP	10	386.00
23085	10	G 1/2"	25	14	62	32	PVDF	1	188.00
23087	12	G 1/4"	20	12	58	32	PP	5	248.00
23089	12	G 1/4"	20	12	58	32	PVDF	1	186.00
23091	12	G 3/8"	20	12	58	32	PP	5	244.00
23092	12	G 3/8"	20	12	58	32	PTFE	1	205.00
23093	12	G 3/8"	20	12	58	32	PVDF	1	186.00
23095	12	G 1/2"	25	14	64	34	PP	5	270.00
23097	12	G 1/2"	25	14	64	34	PVDF	1	144.00
23099	14	G 1/4"	25	12	64	34	PP	3	270.00
23101	14	G 1/4"	25	12	64	34	PVDF	1	142.00
23103	14	G 3/8"	25	12	64	34	PP	3	284.00
23105	14	G 3/8"	25	12	64	34	PVDF	1	155.00
23107	14	G 1/2"	25	14	64	36	PP	3	302.00
23109	14	G 1/2"	25	14	64	36	PVDF	1	160.00
10687	4	NPT 1/8"	15	10	48	25	PP	10	150.00
10689	4	NPT 1/8"	15	10	48	25	PVDF	1	124.00
10690	4	NPT 1/4"	15	15	48	30	PP	10	150.00
10692	4	NPT 1/4"	15	15	48	30	PVDF	1	110.00
10693	4	NPT 3/8"	20	15	54	30	PP	10	300.00
10695	4	NPT 3/8"	20	15	54	30	PVDF	1	144.00
10696	4	NPT 1/2"	25	20	60	35	PP	10	322.00
10698	4	NPT 1/2"	25	20	60	35	PVDF	1	156.00
23111	6	NPT 1/8"	15	10	48	25	PP	10	150.00
23113	6	NPT 1/8"	15	10	48	25	PVDF	1	125.00
23115	6	NPT 1/4"	15	15	48	30	PP	10	150.00
23117	6	NPT 1/4"	15	15	48	30	PVDF	1	125.00
23119	6	NPT 3/8"	20	15	54	30	PP	10	290.00
23121	6	NPT 3/8"	20	15	54	30	PVDF	1	144.00
23123	6	NPT 1/2"	25	20	60	35	PP	10	304.00
23125	6	NPT 1/2"	25	20	60	35	PVDF	1	157.00
23127	8	NPT 1/8"	15	10	48	26	PP	10	322.00
23129	8	NPT 1/8"	15	10	48	26	PVDF	1	157.00
23131	8	NPT 1/4"	15	15	48	31	PP	10	322.00
23133	8	NPT 1/4"	15	15	48	31	PVDF	1	157.00
23135	8	NPT 3/8"	20	15	54	31	PP	10	328.00
23137	8	NPT 3/8"	20	15	54	31	PVDF	1	156.00
23139	8	NPT 1/2"	25	20	60	36	PP	10	364.00
23141	8	NPT 1/2"	25	20	60	36	PVDF	1	185.00
23143	10	NPT 1/8"	20	10	56	28	PP	10	364.00
23145	10	NPT 1/8"	20	10	56	28	PVDF	1	185.00
23147	10	NPT 1/4"	20	15	56	33	PP	10	364.00
23149	10	NPT 1/4"	20	15	56	33	PVDF	1	185.00
23151	10	NPT 3/8"	20	15	56	33	PP	10	364.00
23153	10	NPT 3/8"	20	15	56	33	PVDF	1	185.00
23155	10	NPT 1/2"	25	20	62	38	PP	10	380.00
23157	10	NPT 1/2"	25	20	62	38	PVDF	1	185.00
23159	12	NPT 1/4"	20	15	58	38	PP	5	248.00
23161	12	NPT 1/4"	20	15	58	38	PVDF	1	184.00
23163	12	NPT 3/8"	20	15	58	38	PP	5	244.00
23165	12	NPT 3/8"	20	15	58	35	PVDF	1	184.00
23167	12	NPT 1/2"	25	20	64	40	PP	5	280.00
23169	12	NPT 1/2"	25	20	64	40	PVDF	1	188.00
23171	14	NPT 1/4"	25	15	64	37	PP	3	270.00
23173	14	NPT 1/4"	25	15	64	37	PVDF	1	180.00
23175	14	NPT 3/8"	25	15	64	37	PP	3	284.00
23177	14	NPT 3/8"	25	15	64	37	PVDF	1	190.00
23179	14	NPT 1/2"	25	20	64	42	PP	3	310.00
23181	14	NPT 1/2"	25	20	64	42	PVDF	1	197.00
23183	6	M10 x 1,5	15	8	48	23	PP	10	a.A.
23185	6	M10 x 1,5	15	8	48	23	PVDF	5	a.A.
23187	6	M12 x 1,5	15	12	48	27	PP	10	a.A.
23189	6	M12 x 1,5	15	12	48	27	PVDF	2	a.A.
23191	6	M16 x 1,5	20	12	54	27	PP	10	a.A.
23193	6	M16 x 1,5	20	12	54	27	PVDF	2	a.A.
23195	6	M18 x 1,5	20	12	54	27	PP	5	a.A.
23197	6	M18 x 1,5	20	12	54	27	PVDF	2	a.A.
23199	8	M10 x 1,5	15	8	48	24	PP	10	a.A.
23201	8	M10 x 1,5	15	8	48	24	PVDF	2	a.A.
23203	8	M12 x 1,5	15	12	48	28	PP	10	a.A.
23205	8	M12 x 1,5	15	12	48	28	PVDF	2	a.A.
23207	8	M16 x 1,5	20	12	54	28	PP	10	a.A.
23209	8	M16 x 1,5	20	12	54	28	PVDF	2	a.A.
23211	8	M18 x 1,5	20	12	54	28	PP	5	a.A.
23213	8	M18 x 1,5	20	12	54	28	PVDF	2	a.A.
23215	10	M10 x 1,5	20	8	56	26	PP	10	a.A.
23217	10	M10 x 1,5	20	8	56	26	PVDF	1	119.00
23219	10	M12 x 1,5	20	12	56	30	PP	10	a.A.
23221	10	M12 x 1,5	20	12	56	30	PVDF	2	a.A.
23223	10	M16 x 1,5	20	12	56	30	PP	5	a.A.
23225	10	M16 x 1,5	20	12	56	30	PVDF	2	a.A.
23227	10	M18 x 1,5	20	12	56	30	PP	5	a.A.
23229	10	M18 x 1,5	20	12	56	30	PVDF	2	a.A.
23231	12	M12 x 1,5	20	12	58	32	PP	5	a.A.
23233	12	M12 x 1,5	20	12	58	32	PVDF	2	a.A.
23235	12	M14 x 1,5	20	12	58	32	PP	5	a.A.
23237	12	M14 x 1,5	20	12	58	32	PVDF	2	a.A.
23239	12	M16 x 1,5	20	12	58	32	PP	5	a.A.
23241	12	M16 x 1,5	20	12	58	32	PVDF	2	a.A.
23243	12	M18 x 1,5	20	12	58	32	PP	5	a.A.
23245	12	M18 x 1,5	20	12	58	32	PVDF	2	a.A.
23247	14	M12 x 1,5	25	12	64	34	PP	5	a.A.
23249	14	M12 x 1,5	25	12	64	34	PVDF	2	a.A.
23251	14	M16 x 1,5	25	12	64	34	PP	5	a.A.
23253	14	M16 x 1,5	25	12	64	34	PVDF	2	a.A.
23255	14	M18 x 1,5	25	12	64	34	PP	5	a.A.
23257	14	M18 x 1,5	25	12	64	34	PVDF	1	a.A.