High-Tech Flowmeter for Gases

Product specification Precisely operating, compact flowmeters with measuring tube, needle... more

Product specification

Precisely operating, compact flowmeters with measuring tube, needle fine regulating valve and connecting fittings as complete unit.

Identical to Type MULTIFIT^®-EMP-K4, part 24875, but with glass ball float for measurement of gases.

Technical specification

Max. operating pressure: 3 bar

Max. temperature: +70 °C

General Information The flowmeters EMP-4 operate in accordance with the float measuring... more

Close menu

General Information

The flowmeters EMP-4 operate in accordance with the float measuring principle. At constant flow speed, the float in the conical measuring tube comes to rest as soon as the resistibility / flow force compensates, at the corresponding cross section, the inertial forces acting on the float. When the flow speed changes, e.g. by pressure change, the float moves freely up and down until the resistibility, altering with the free cross-sectional flow area, has stabilized at the value of inertial forces and an equilibrium of forces is again prevalent. The position of the float reached in this manner corresponds to a specific volumetric flow and is indicated as flow rate on the scale printed on measuring tube.

Precisely operating, compact flowmeters with measuring tube, needle fine regulating valve and connecting fittings as complete unit.

Housing parts are made of high-quality plastics and injection-molded.

The very accurate reading is enabled by a calibrated ribbed measuring tube, through which the ball float (for measurement of gases) or cone float are precisely conducted.

A pipe of acrylic glass protects the measuring tube against contaminations and break.

The fine regulating valve allows the exact adjustment of very small measuring intervals.

The flowmeters are supplied alternatively with or without annular proximity switch (flow controller).

Standardly, the flowmeters are fitted with screw-in tubing joints accepting tubes and pipes made of PP (polypropylene), PVDF (polyvinylidene fluoride) or PFA (perfluoroalkoxy) with inside diameter of 4 mm and outside diameter of 6 mm. Alternatively, these connections can be replaced by other fittings accepting tubes or pipes with different outside diameters. The screw joint bodies are screwed into an internal thread G.

Connections with bulkhead nut for wall mounting or control panel mounting.

Rear connections allow a close alignment of the flowmeters.

The measuring tube consists of pure DURAN glass of highest quality.

Accuracy class of the glass tube 2.5 according to VDI / VDE

Very good corrosion resistance to most measuring media except to hot, concentrated alkalis and hydrofluoric acid.

Due to its high boric oxide content (BO₃) the DURAN glass exhibits a high thermal shock resistance, which is reflected in an extremely low linear expansion coefficient of k = 3.2 * 10^-6 m/K.

Four different measuring tubes with diameters of 10, 17 and 28 mm and lengths of 75 and 150 mm offer numerous solutions for a wide variety of applications.

Item	Measuring range gases¹ l/h	Ø-Messrohr mm	Länge Messrohr mm	Werkstoff	Innengewinde	Einheit Stück	Price Euro*
305098	4 - 40	10	75	PP	G 1/8"	1	304.00
305100	4 - 40	10	75	PVDF	G 1/8"	1	339.00
305102	4 - 40	10	75	PFA	G 1/8"	1	379.00
3050981	10 - 100	10	75	PP	G 1/8"	1	304.00
3051001	10 - 100	10	75	PVDF	G 1/8"	1	339.00
3051021	10 - 100	10	75	PFA	G 1/8"	1	379.00
305099	40 - 400	17	75	PP	G 1/4"	1	324.00
305101	40 - 400	17	75	PVDF	G 1/4"	1	345.00
305103	40 - 400	17	75	PFA	G 1/4"	1	388.00
3050991	150 - 1600	17	75	PP	G 1/4"	1	324.00
3051011	150 - 1600	17	75	PVDF	G 1/4"	1	345.00
3051031	150 - 1600	17	75	PFA	G 1/4"	1	388.00
305057	250 - 2500	28	150	PP	G 1/2"	1	895.00
305065	250 - 2500	28	150	PVDF	G 1/2"	1	946.00
305073	250 - 2500	28	150	PFA	G 1/2"	1	1,015.00
305081	600 - 6000	28	150	PP	G 1/2"	1	895.00
305089	600 - 6000	28	150	PVDF	G 1/2"	1	946.00
305094	600 - 6000	28	150	PFA	G 1/2"	1	1,015.00