gtag('event', 'view_item', { "items": [{ "item_id": "G337735", "item_name": "Washer (DIN 9021) made of PP", "item_brand": "Reichelt", "item_category": "Fasteners", "item_category2": "Washers and Rings", "price": 1 }]});
+49 (0) 6221-3125-0 (Mon-Wed 8 am - 17 pm, Thu-Fri 8 am - 16 pm)

Washer (DIN 9021) made of PP

Technical specification Material: PP (polypropylene) Colour: natural... more

Technical specification

Material: PP (polypropylene)

Colour: natural

Regulations: DIN 9021

General Information Resistant to corrosion, abrasion and to most chemicals Extremely good... more

General Information

Resistant to corrosion, abrasion and to most chemicals

Extremely good impact toughness and notch impact strength

High surface hardness

Resistant to hydrolysis

Insulating against moisture and electricity

This material should not be used at freezing temperatures, because of embrittlement at temperatures below 0 °C

Chemical features:

Good resistance to alcohols, ketones, alkalis and acids (except strong and oxidizing acids); resistant to fats and oils, including mineral oils and fuels.

Material specification:

PP (polypropylene) is a universally usable standard plastic with excellent properties

PP is sterilizable and has good electrical properties

Weldable; bondable only after pretreatment

PP is similar to PE (polyethylene), but more fat- and oil-resistant, and also features a higher hardness and stiffness than HDPE as well as a better resilience; its impact strength is, however, lower

UV-radiation and weather: limited resistance

Material: PP (polypropylene)

Colour: natural

Density: 0.90 g/cm3 (DIN 53479)

Temperature range: 0 to +100 °C

Elastic modulus: 1,350 N/mm2 (ISO 527)

Yield stress: 30 N/mm2 (ISO 527-1)

Tearing strength: 25 - 40 N/mm2 (DIN 53455)

Elongation at break: 70 % (DIN 53455)

Impact resistance: without break (DIN 53453)

Notch impact strength: 7 kJ/m2 (DIN 53453)

Ball pressure hardness: 70 N/mm2 (DIN 53456)

Coefficient of sliding friction against steel (dry): approx. 0.30 - 0.40

Thermal conductivity: 0.22 W/m * K (DIN 52612)

Shore hardness D: 70° (DIN 53505)

Volume resistivity: 1017 Ohm x cm (DIN 53482)

Surface resistance: 1013 Ohm (DIN 53482)

Dielectric constant: 2.27 at 50 Hz (DIN 53483)

Item Image For thread d
mm
D
mm
h
mm
Einheit
Stück
Price
Euro*
Buy
337735
M3 3,2 9 0,8 50 22.00
337736
M3 3,2 9 0,8 100 36.00
337737
M4 4,3 12 1 50 24.00
337738
M4 4,3 12 1 100 39.00
337739
M5 5,3 15 1,2 50 26.00
337740
M5 5,3 15 1,2 100 43.00
337741
M6 6,4 18 1,6 50 43.00
337742
M6 6,4 18 1,6 100 73.00
337743
M8 8,4 24 2 50 56.00
337744
M8 8,4 24 2 100 95.00
337745
M10 10,5 30 2,5 50 73.00
337746
M10 10,5 30 2,5 100 120.00
337747
M12 13 37 3 50 80.00
337748
M12 13 37 3 100 129.00
337749
M14 15 44 3 50 86.00
337750
M14 15 44 3 100 137.00
337751
M16 17 50 3 25 73.00
337752
M16 17 50 3 50 120.00
337753
M18 20 56 4 25 78.00
337754
M18 20 56 4 50 131.00
337755
M20 22 60 4 25 93.00
337756
M20 22 60 4 50 152.00
Similar products
Viewed